adjustable-angle tablet-stand 3d printing 3D 프린트 모델

$
5.00
가지고 있는 아이템 $0.00 크레딧. 크레딧 구입
- 이용 가능한 포맷: Autodesk 3DS MAX (.max) 683.73 kb
- 컬렉션:
- 프린트 준비:
- 3D 스캔:No
- 성인용 콘텐츠:No
- PBR:No
- 조회:4658
- 날짜: 2021-12-23
- 아이템 ID:379767
please see latest update below!
this is my design for a print-as-one (print-in-place) hinged tablet stand that can be adjusted over a wide range of incline angles. i was looking around on thingiverse for something of this nature but could only find adjustable ones that need screws and nuts to assemble, or some other post-print assembly. i thought there must be a better way!
this will work straight off the print bed. just peel away the brim and very carefully loosen the hinges and you're good to go. i've been using it with a large 9.7" galaxy tab s2 with a case on and it supports it nicely and feels very stable.
when you first unfold it, the inner two parts have to swing all the way round the outer base piece so that it brings the supports on to the top side of the base where the position notches are located. then to put it away flat, just rotate all the way round to the back again.
there may well be a few improvements that could be made to the design, but i would welcome any comments and suggestions! at the moment, the supports are spaced a little too wide to use for my samsung galaxy s5 smartphone, so i have considered maybe a smaller version to accommodate phones as well. not sure if the narrower design would become unstable for large tablets though.
더 보기this is my design for a print-as-one (print-in-place) hinged tablet stand that can be adjusted over a wide range of incline angles. i was looking around on thingiverse for something of this nature but could only find adjustable ones that need screws and nuts to assemble, or some other post-print assembly. i thought there must be a better way!
this will work straight off the print bed. just peel away the brim and very carefully loosen the hinges and you're good to go. i've been using it with a large 9.7" galaxy tab s2 with a case on and it supports it nicely and feels very stable.
when you first unfold it, the inner two parts have to swing all the way round the outer base piece so that it brings the supports on to the top side of the base where the position notches are located. then to put it away flat, just rotate all the way round to the back again.
there may well be a few improvements that could be made to the design, but i would welcome any comments and suggestions! at the moment, the supports are spaced a little too wide to use for my samsung galaxy s5 smartphone, so i have considered maybe a smaller version to accommodate phones as well. not sure if the narrower design would become unstable for large tablets though.
다른 포맷이 필요하세요?
다른 포맷이 필요하시면, 새로운 지원 티켓을 열어 요청하세요. 저희는 3D 모델을 다음으로 변환할 수 있습니다: .stl, .c4d, .obj, .fbx, .ma/.mb, .3ds, .3dm, .dxf/.dwg, .max. .blend, .skp, .glb. 우리는 3D 장면을 변환하지 않습니다 .step, .iges, .stp, .sldprt와 같은 형식도 포함됩니다.!
다른 포맷이 필요하시면, 새로운 지원 티켓을 열어 요청하세요. 저희는 3D 모델을 다음으로 변환할 수 있습니다: .stl, .c4d, .obj, .fbx, .ma/.mb, .3ds, .3dm, .dxf/.dwg, .max. .blend, .skp, .glb. 우리는 3D 장면을 변환하지 않습니다 .step, .iges, .stp, .sldprt와 같은 형식도 포함됩니다.!
adjustable-angle tablet-stand 3d printing 3D 프린트 모델 max, 발신 3DPrinting
3d 3dprinting 3dprint이 아이템에 대한 코멘트 없음.