groot Modello di stampa 3D

groot Modello di stampa 3D stl, Da teduk

this model will look outstanding if printed on sla/sls 3d printer. the accuracy of the model printed on fff printer can vary from the result shown in the pictures.

this model was tested in cura 2.3.1. to avoid printing problems, we recommend the following settings: quality layer height: 0.1 mm initial layer height: 0.3 mm line width: 0.4 mm wall line width: 0.4 mm outer wall line width: 0.4 mm inner wall(s) line width: 0.4 mm top/bottom line width: 0.4 mm infill line width: 0.4 mm skirt/brim line width: 0.4 mm support line width: 0.4 mm

shell wall thickness: 0.8 mm wall line count: 2 top/bottom thickness: 0.8 mm top thickness: 0.8 mm top layers: 8 bottom thickness: 0.8 mm bottom layers: 8 top/bottom pattern: lines outer wall inset: 0 mm compensate wall overlaps: check compensate outer wall overlaps: check compensate inner wall overlaps: check horizontal expansion: 0 mm z seam alignment: shortest

infill infill density: 25% infill line distance: 3.2 mm infill pattern: grid infill overlap percentage: 10% infill overlap: 0.04 mm skin overlap percentage: 5% skin overlap: 0.02 mm infill wipe distance: 0.1 mm infill layer thickness: 0.1 mm gradual infill steps: 0 infill before walls: check

material enable retraction: check retraction extra prime amount: 0 mm3 retraction minimum travel: 0.8 mm maximum retraction count: 90 minimum extrusion distance window: 6.5 mm standby temperature: 175°c nozzle switch retraction distance: 16 mm nozzle switch retraction speed: 20 mm/s nozzle switch retract speed: 20 mm/s nozzle switch prime speed: 20 mm/s

speed print speed: 60 mm/s infill speed: 80 mm/s wall speed: 30 mm/s outer wall speed: 30 mm/s inner wall speed: 60 mm/s top/bottom speed 15 mm/s support speed: 60 mm/s support infill speed: 60 mm/s travel speed: 120 mm/s initial layer speed: 15 mm/s initial layer print speed: 15 mm/s initial layer travel speed: 30 mm/s skirt/brim speed 15 mm/s maximum z speed: 0 mm/s

travel combing mode: all avoid printed parts when traveling: check travel avoid distance: 0.625 mm

cooling enable print cooling: check fan speed: 100% regular fan speed: 100% maximum fan speed: 100% regular/maximum fan speed threshold: 10 s regular fan speed at height: 0.3 mm regular fan speed at layer: 2 minimum layer time: 5 s minimum speed: 10 mm/s

support enable support: check support placement: everywhere support overhang angle: 50° support pattern: zig zag connect support zigzags: check support density: 30 % support line distance: 1.3333 mm support z distance: 0.1 mm support top distance: 0.1 mm support bottom distance: 0.1 mm support x/y distance: 0.7 mm support distance priority: z overrides x/y minimum support x/y distance: 0.2 mm support stair step height: 0.3 mm support join distance: 2.0 mm support horizontal expansion: 0.2 mm use towers: check tower diameter: 3.0 mm minimum diameter: 3.0 mm tower roof angle: 65°

build plate adhesion build plate adhesion type: brim skirt/brim minimum length: 250 mm brim width: 8.0 mm brim line count: 20 brim only on outside: check

mesh fixes union overlapping volumes: check special modes print sequence: all at once surface mode: normal

experimental extra skin wall count: 0